Synthesis of partially fluorinated poly(arylene ether sulfone) multiblock copolymers bearing perfluorosulfonic functions

Partially fluorinated poly(arylene ether sulfone) multiblock copolymers bearing perfluorosulfonic functions (ps‐PES‐FPES), with ionic exchange capacity (IEC) ranging between 0.9 and 1.5 meq H⁺/g, are synthesized by regioselective bromination of partially fluorinated poly(arylene ether sulfone) multiblock copolymers (PES‐FPES), followed by Ullman coupling reaction with lithium 1,1,2,2‐tetrafluoro‐2‐(1,1,2,2‐tetrafluoro‐2‐iodoethoxy)ethanesulfonate. The PES‐FPES are prepared by aromatic nucleophilic substitution reaction by an original approach, that is, “one pot two reactions synthesis.” The chemical structures of polymers are analyzed by ¹H and ¹⁹F NMR spectroscopy. The resulted ionomers present two distinct glass transitions and α relaxations revealing phase separation between the hydrophilic and the hydrophobic domains. The phase separation is observed at much lower block lengths of ps‐PES‐FPES as compared with the literature. AFM and SANS observations supported the phase separation, the hydrophilic domains are well dispersed but the connectivity to each other depends on the ps‐PES block lengths. The thermomechanical behavior, the water up‐take, and the conductivity of the ps‐PES‐FPES membranes are compared with those of Nafion 117^® and randomly functionalized polysulfone (ps‐PES). Conductivities close or higher to those of Nafion 117^® are obtained. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1941–1956     

Lysine‐based functional blocked isocyanates for the preparation of polyurethanes provided with pendant side groups

This article describes a methodology to prepare polyurethanes (PUs), decorated with pendant (bio)functional side groups, by polymerizing (bio)functionalized blocked diisocyanates with polyols. Caprolactam blocked lysine diisocyanate methyl ester (BLDI‐OMe) was prepared in high yields, by reacting the methyl ester of lysine with carbonyl biscaprolactam. In the absence of a catalyst, the polymerization of BLDI‐OMe with polycaprolactone and polytetrahydrofuran resulted in strictly linear PUs due to the high selective reactivity of the blocked isocyanates (BIs). Although the ester appeared to be less reactive, we found hydrolyzing conditions for the ester, without affecting the BIs. The free acid groups were converted into a N‐hydroxysuccinimide (NHS) activated ester, which was a versatile intermediate for further functionalization. After having demonstrated that model amines were able to substitute NHS without effecting the BIs groups, the same chemistry was used to couple biotin, giving a biotin functional caprolactam blocked lysine diisocyanate. The polymerization with polyols afforded the corresponding biotin‐functional PUs. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2036–2049     

Synthesis,self-assembly and photo-responsive behavior of AB2 shaped amphiphilic azo block copolymer

In this work, we report the synthesis of AB2 shaped amphiphilic azo block copolymer by macromolecular azo coupling reaction. The product and intermediates were characterized by various methods. The selfassembly in selected solvents and photo-responsive behavior of the copolymer were studied by means of UV–vis spectrophotometry and TEM. Spherical aggregates can be obtained by gradually adding water into the solution of this amphiphilic azo block copolymer. Upon irradiation with polarized UV(365 nm)light, the aggregates can be elongated in the polarized direction.     

Topological “interfacial” polymer chemistry: Dependency of polymer “shape” on surface morphology and stability of layer structures when heating organized molecular films of cyclic and linear block copolymers of n‐butyl acrylate‐ethylene oxide

The “topological polymer chemistry” of amphiphilic linear and cyclic block copolymers at an air/water interface was investigated. A cyclic copolymer and two linear copolymers (AB‐type diblock and ABA‐type triblock copolymers) synthesized from the same monomers were used in this study. Relatively stable monolayers of these three copolymers were observed to form at an air/water interface. Similar condensed‐phase temperature‐dependent behaviors were observed in surface pressure–area isotherms for these three monolayers. Molecular orientations at the air/water interface for the two linear block copolymers were similar to that of the cyclic block copolymer. Atomic force microscopic observations of transferred films for the three polymer types revealed the formation of monolayers with very similar morphologies at the mesoscopic scale at room temperature and constant compression speed. ABA‐type triblock linear copolymers adopted a fiber‐like surface morphology via two‐dimensional crystallization at low compression speeds. In contrast, the cyclic block copolymer formed a shapeless domain. Temperature‐controlled out‐of‐plane X‐ray diffraction (XRD) analysis of Langmuir–Blodgett (LB) films fabricated from both amphiphilic linear and cyclic block copolymers was performed to estimate the layer regularity at higher temperatures. Excellent heat‐resistant properties of organized molecular films created from the cyclic copolymer were confirmed. Both copolymer types showed clear diffraction peaks at room temperature, indicating the formation of highly ordered layer structures. However, the layer structures of the linear copolymers gradually disordered when heated. Conversely, the regularity of cyclic copolymer LB multilayers did not change with heating up to 50 °C. Higher‐order reflections (d₀₀₂, d₀₀₃) in the XRD patterns were also unchanged, indicative of a highly ordered structure. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 486–498     

Controlled synthesis of amphiphilic block copolymers based on poly(isobutylene) macromonomers

The synthesis of a monoacrylate functionalized poly(isobutylene) (PIB) macromonomer (PIBA) has been achieved by a two‐step reaction starting from a commercially available PIB. Firstly, terminal olefins (vinylidene and trisubstituted olefin) of PIB were transformed to a phenolic residue by Friedel‐Crafts alkylation followed by subsequent esterification of the phenol with acryloyl chloride, catalyzed by triethylamine. PIBA structure was confirmed by ¹H‐NMR, ¹³C‐NMR and GPC before utilizing in the RAFT copolymerization with N,N‐dimethylacrylamide (DMA) to obtain statistical copolymers (P[(DMA‐co‐(PIBA)]). Monomer conversions were consistently higher than 85% for both DMA and PIBA as monomer feed composition was varied. Chain extension of poly(N,N‐dimethylacrylamide) with PIBA to synthesize block copolymers (P[(DMA‐b‐(PIBA)]) was also achieved with near quantitative monomer conversions (>97%). Block formation efficiency was not quantitative but purification of block copolymers was possible by selective precipitation. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 634–643     

The pH induced vesicle to micelle morphology transition of a THP‐protected polymer

A diblock copolymer consisting of tetrahydropyranyl acrylate (THPA) as a pH‐deprotectable block, and a permanently hydrophobic block, methyl acrylate, was synthesized by RAFT polymerization using a quaternary amine functionalized, hydrophilic, RAFT chain transfer agent. The polymer self‐assembled in water to form vesicles with D_h = 130 nm, as determined by DLS and cryogenic transmission electron microscopy. Acid catalyzed deprotection of the THPA units to yield acrylic acid resulted in a vesicle to micelle morphology transition, as evidenced by the decrease in hydrodynamic diameter to D_h = 19 nm and the observation of micelles by dry state transmission electron microscopy. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3026–3031     

Thermal analysis and FT‐IR studies of adsorbed poly(ethylene‐stat‐vinyl acetate) on silica

Adsorbed poly(ethylene‐stat‐vinyl acetate) (PEVAc) on fumed silica was studied using temperature‐modulated differential scanning calorimetry (TMDSC) and FT‐IR spectroscopy. The properties of the copolymers were compared with poly(vinyl acetate) (PVAc) and low density polyethylene (LDPE) as references. TMDSC analysis of the copolymer‐silica samples in the glass transition region was complicated for the copolymers because of the ethylene crystallinity. Nevertheless, examination of the glass transition region for small adsorbed amounts of these copolymers indicated the presence of tightly‐ and loosely‐bound polymer segments, similar to other polymers which have an attraction to silica. Compared with bulk polymers with the same composition, the tightly‐bound polymers showed an increased glass transition temperature (T_g) and a loosely‐bound fraction with a lower T_g than bulk. FT‐IR spectra of the surface copolymers indicated that the fraction of bound carbonyls (p) increased as the fraction of vinyl acetate in the copolymers decreased, consistent with the notion that the carbonyls from vinyl acetate preferentially find their way to the silica surface. Spectra from samples with different adsorbed amounts of polymer were used to obtain the amount of bound polymer (M_b) and the ratio of molar absorption coefficients of bound carbonyls to free carbonyls (X). The copolymers had very large p values (up to 0.8) at small adsorbed amounts and dependent on the composition of the polymer. However, an analysis of the bound fractions, based on only the vinyl acetate groups, superimposed the data, suggesting that the ethylene units simply dilute the vinyl acetate groups in the surface polymer. The sample with the smallest fraction of vinyl acetate did not show this behavior and may be considered to be “carbonyl poor.” © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 727–736     

Micellar core-shell-type acrylic-polyurethane hybrid materials with self-polishing property

Abstract

Marine fouling can be a serious problem in the shipping industry, since it increases the surface roughness of the hull and hence its frictional resistance to its movement through water. Antifouling paint can be defined as preventing the attachment of marine organisms onto surfaces. However, the most commonly used antifouling coating which is the tributyltin-based self-polishing copolymer causes the severe pollution of marine environment. Ammonium salt-based paints include tertiary amines as biocides which have effective biocidal and biodegradable properties without accumulation in the sea environment. However, ammonium salt-based coatings were too sensitive to seawater and became swollen. In this study, polyurethane-acrylic copolymers were synthesized by radical polymerization. These hybrid materials were found to form core–shell structures in aqueous media. Synthesis and properties of copolymers were investigated by Fourier transform-infrared spectrometer, proton-nuclear magnetic resonance, transmission electron microscopy, and dynamic light scattering. The polishing rate of self-polishing copolymer was determined from the reduction in dry film thickness after artificial seawater immersion under a dynamic condition.     

Morphology,thermo-mechanical properties and surface hydrophobicity of nanostructured epoxy thermosets modified with PEO-PPO-PEO triblock copolymer

In this paper, we report on the effect of amphiphilic poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (PEO-PPO-PEO) triblock copolymer (TBCP) on the miscibility, phase separation, thermomechanical properties and surface hydrophobicity of diglycidyl ether of bisphenol-A (DGEBA)/4,4'-diaminodiphenylmethane (DDM) system. The blends were nanostructured. The phase separation occurred via self-assembly of PPO blocks followed by the reaction induced phase separation of PEO blocks. The surface roughness increased with increase in concentration of TBCP due to increased phase separation of PEO blocks at higher concentration. The phase separated PEO blocks formed the crystalline phase in the amorphous crosslinked epoxy matrix. The TBCP has a strong plasticizing effect on the matrix and decreased the glass transition temperature (T_g) and modulus of the thermoset. The incorporation of TBCP improved impact strength and tensile properties and 5 phr TBCP content was found to be optimum to achieve balanced mechanical performance. Moreover, the thermal stability of the epoxy system was retained while hydrophobicity was improved in the presence of TBCP.     

Block copolymers containing polyacrylamide and polyacrylic acid: Bulk structure and hydrogen bonds system

Asymmetric block copolymers PAAc-b-PAAm (DBCs) and PAAm-b-PAAc-b-PAAm (TBCs) comprised poly(acrylic acid) blocks of constant chain length and polyacrylamide blocks of variable chain length were synthesized using RAFT/MADIX technique. Their properties in a bulk state were studied by differential scanning calorimetry and the hydrogen bond system was investigated by Fourier transform infrared spectroscopy. It was found that DBCs and TBCs possess a homogeneous amorphous structure, whose temperatures of glass transition and destruction beginning increased with growth of PAAm block length. The H-bond system between PAAc and PAAm blocks was most developed in TBC sample and formed manly by the mixed cyclic dimmers of carboxyl and amide groups.